Free shipping on wraparound lenses & select items

A cracked vapor proof light cover can turn a working fixture into a maintenance problem fast. In a wash bay, parking garage, food prep area, utility room, or basement, the cover is not just there to soften glare. It helps keep moisture, dust, insects, and incidental impact away from the lamp or LED components inside.

The good news is that a damaged cover does not automatically mean the entire fixture needs to be replaced. When the housing, wiring, and light source are still in usable condition, matching the right replacement lens, tube, or enclosure component can be the faster and more cost-effective repair.

What Is a Vapor Proof Light?

A vapor proof light is commonly used to describe an enclosed fixture designed for environments where humidity, condensation, dust, or splashing water may be a concern. You may also see similar fixtures called vapor-tight, vapor-proof, gasketed, enclosed-and-gasketed, or wet-location fixtures. The exact rating matters, so do not assume every enclosed fixture is suitable for the same conditions.

Most traditional vapor-tight fixtures use a long plastic lens or tube over fluorescent lamps, secured to a metal or fiberglass housing with gaskets, end caps, clips, or latches. LED versions may use an integrated sealed lens and LED board. Both styles protect the light source, but their replacement options are different.

If the fixture has replaceable lamps or a removable plastic lens, replacing the damaged plastic component may extend its service life significantly. If the LED board, driver, or molded enclosure has failed, a full fixture replacement may make more sense. The right answer depends on what is actually damaged.

Why the Cover Matters More Than It Looks

A yellowed, brittle, or missing cover changes more than appearance. It can reduce usable light output, expose electrical components to contamination, and create a safety issue if plastic fragments break loose. In facilities with cleaning routines, airborne dust, or high humidity, a poor seal can also shorten the life of lamps, drivers, and internal wiring.

Plastic lenses age differently depending on the material and environment. Acrylic generally provides good clarity and is a practical choice for many indoor applications, but it can crack under impact. Polycarbonate has much higher impact resistance and is often preferred where accidental contact, vibration, or rougher conditions are expected. The material used in the original fixture may also be shaped or frosted to control glare and distribute light evenly.

That is why a clear tube that happens to fit loosely is not always a good replacement. The cover needs to fit the housing correctly, work with the fixture’s seals and clips, and provide the light distribution the space needs.

First, Identify What Needs Replacing

Before ordering a replacement, shut off power to the fixture and inspect it carefully. A cover replacement is a sensible repair when the housing is sound, the mounting points are intact, and there is no evidence of heat damage or serious corrosion.

Look at the lens itself. Is it a one-piece rounded tube, a flat panel, a wraparound lens, or a formed diffuser secured by end caps? Check whether the end caps, gaskets, retaining clips, and latches are still present. A new cover cannot restore a proper seal if the parts that hold it in place are bent, missing, or deteriorated.

Also inspect the source of the damage. If a forklift strike, overhead door, or repeated vibration broke the original lens, choosing a more impact-resistant material may be worthwhile. If discoloration is the main issue, the fixture may simply need a replacement cover with comparable diffusion and light transmission.

For an LED fixture, determine whether the lens is designed to come off separately. Some LED vapor-tight fixtures have serviceable covers. Others are factory-sealed assemblies, and forcing the lens loose can damage the gasket or housing.

How to Measure a Replacement Cover Correctly

Measurements are where many otherwise simple repairs go wrong. Do not rely only on the nominal fixture length, such as four feet or eight feet. A four-foot fixture may use a lens with a different overall length, end profile, diameter, or mounting channel than another four-foot fixture.

Measure the old cover if it is available, even if it is cracked. Record its overall length from end to end, outside width or diameter at the widest point, and the shape of the cross-section. If it has lips, flanges, grooves, or side rails, measure those as well. These details determine how the replacement engages with the housing.

Take photos of the fixture from several angles, including the end caps, clips, labels, and the lens profile. If there is a manufacturer name, catalog number, or molded part number, capture that too. A label can be helpful, but measurements and photos are often more reliable when fixtures have been modified over the years.

For a tube-style cover, measure the tube diameter and note whether the ends are open, capped, flanged, or fitted into separate end pieces. For a formed wraparound lens, measure the flat center section, both side drops, and any retaining edges. When in doubt, provide slightly more information rather than less. It is much easier to verify a match before fabrication or shipment than after a part has arrived.

Match the Material to the Environment

Replacement covers are not one-size-fits-all, especially in working environments. The best choice balances clarity, diffusion, impact resistance, chemical exposure, temperature, and cost.

Acrylic is often a good fit for offices, hallways, utility areas, and other locations where clarity and a clean appearance matter more than impact resistance. Polycarbonate is better suited to garages, warehouses, workshops, schools, and areas where a lens may be struck or flexed. For applications involving cleaning chemicals, oils, heat, or unusual environmental exposure, confirm material compatibility before selecting a replacement.

Light output is another trade-off. Clear plastic allows more direct light through but can produce glare and reveal the lamps or LEDs. Prismatic, frosted, or ribbed diffusion spreads light more comfortably and can conceal internal components, though it may reduce transmission slightly. For task areas, that difference can affect how the space feels and functions.

If the original lens had a particular pattern, try to match it rather than switching materials solely because the dimensions are close. The optics of the cover are part of the fixture’s design.

When a Custom Replacement Is the Better Repair

Older fixtures often outlast the parts made for them. This is especially common in commercial buildings, multifamily properties, schools, industrial spaces, and homes with long-installed utility lighting. A replacement part may be discontinued even though the housing is still in excellent shape.

Custom fabrication can be practical when a standard vapor proof light cover is unavailable, the fixture uses an unusual profile, or multiple matching covers are needed for a renovation. A physical sample is ideal when possible, but clear dimensions and photos can also help identify whether a part can be replicated or adapted.

For property managers and facilities teams, replacing covers instead of complete fixtures can reduce labor, avoid unnecessary electrical work, and preserve a consistent appearance across a building. It does not solve every problem. Severely corroded housings, failed ballasts or drivers, damaged wiring, and obsolete fixtures with poor performance may justify replacement. But when the enclosure is the only failed component, restoring it is often the sensible first option.

Common Ordering Mistakes to Avoid

The most common mistake is ordering by fixture length alone. The next is overlooking the mounting method. Two lenses can look nearly identical from below while using completely different side channels or end-cap arrangements.

Avoid assuming a cover is interchangeable because it is clear, white, or approximately the same size. Do not trim a replacement unless the material and fixture design allow it, since cutting can create stress points, interfere with end seals, or leave sharp edges. And do not reuse cracked end caps or flattened gaskets simply because the new lens fits. Those small components are often what keep moisture and debris out.

When replacing several fixtures, inspect each one before ordering in bulk. Buildings frequently contain similar-looking fixtures from different installation periods, and a single batch of covers may not fit every housing.

Questions Customers Often Ask

Can I replace only the lens on a vapor-tight fixture?

Often, yes. If the fixture was designed with a removable lens and the housing, seals, and electrical components are in good condition, a replacement lens can be an effective repair. Check the fixture construction before removing anything.

Is polycarbonate always better than acrylic?

Not always. Polycarbonate offers stronger impact resistance, but acrylic can provide excellent clarity and may be the better value for lower-impact indoor locations. The environment and the original fixture design should guide the choice.

What if I cannot find a part number?

Provide overall dimensions, profile measurements, and clear photos of the lens and housing. For unusual or discontinued parts, a sample can be especially useful for matching the shape and material.

A damaged enclosure should not force a good fixture into the scrap pile. If you have an odd-sized, cracked, or discontinued cover, gather the measurements and photos before making a replacement decision. Fluorolite can help evaluate standard and custom options so the repair fits the fixture, the environment, and the job at hand.